Modbus Gateways

Modbus Gateways

Modbus Gateways
There are 54 products.
EtherNet/IP to Modbus RTU/TCP Gateway, PoE, DIN-Rail

EtherNet/IP Scanner, Modbus TCP server
Modbus RTU slave via RS-485/RS-422
32-bit MCU
10/100 Base-TX RJ-45 with PoE 802.3af
10-pin removable terminal block
DIN-Rail mounting
Humidity 10-90% RH, non-condensing
Storage temp -30~+80°C
24VDC, 0.05A power consumption
-25~+75°C (special components required)
52 x 27 x 77.4 mm

180.90 €
Item numberETHER-IP-MODBU-RTU
On the way in
Serial Device Server with 3x RS-232, 2x PoE Ethernet, DIN-Rail

32-bit ARM processor
2 x 10/100 Base-TX RJ45, PoE 802.3af
3 x RS-232, isolated 1000/3000 VDC
Baud rate up to 115200 bps
Data bit 5/6/7/8, stop bit 1/2
Parity None/Odd/Even/Mark/Space
DIN-Rail mounting, plastic casing
PoE or 12-48VDC terminal block
97 x 33 x 126 mm (W x L x H)
-25 to +75C operating temperature
Humidity 10-90% RH non-condensing

233.16 €
Item numberSERIA-DEVIC-SERVE-3X
On the way in
3-Port RS-485/422 Serial Server with 2x PoE Ethernet, DIN-Rail

32-bit ARM CPU
2 x 10/100 RJ45 PoE (802.3af)
3 x RS-485/422 ports
Isolation: 1000/3000 VDC
Baud rate up to 115200 bps
Bias resistor 1 kOhm
Parity None/Odd/Even/Mark/Space
Max 254 node address
12-48VDC terminal block power
97 x 33 x 126 mm
-25 to 75C (special components required)
DIN-Rail mounting

214.40 €
Item numberPORT-RS-485-422-3
On the way in
HART to RS-232/422/485 Gateway with Modbus RTU/ASCII, Loop Power

1-port HART gateway
RS-232 (3-wire) / RS-422 / RS-485
Modbus RTU / Modbus ASCII protocol
Baud rate up to 115200
Supports 2-wire or 4-wire HART devices
Point to Point or Multi-Drop topology
Max. 15 HART devices, burst mode
Loop power output +30V
10-30VDC input, 3.5W max
-40 to +75C (special components required)
25 x 116 x 120 mm, DIN-Rail
10-90% RH non-condensing

493.12 €
Item numberHART-RS-232-422-2
On the way in
Serial Device Server 2-Port RS-232 to Ethernet with PoE

32-bit ARM processor
2 x RS-232 serial ports
1 x 10/100 Base-TX RJ45 PoE
IEEE 802.3af Class 1 PoE powered
Baud rate up to 115200 bps
Auto-negotiating, Auto-MDI/MDIX
Data bit 5/6/7/8, Stop bit 1/2
DIN-Rail mounting, plastic casing
12-48VDC (terminal block)
52 x 95 x 27 mm
-25 to 75C (special components required)
Humidity 10-90% RH non-condensing

134.00 €
Item numberSERIA-DEVIC-SERVE-PORT-3
On the way in
Serial Device Server RS-232/485/422 to Ethernet, PoE, DIN-Rail

32-bit ARM CPU
1 x 10/100 Base-TX RJ45 PoE port
1 x RS-232/RS-485/RS-422 port
Auto-negotiating, Auto-MDI/MDIX
Baud rate up to 115200 bps
Bias resistor 1 K-ohm
Parity: None, Odd, Even, Mark, Space
PoE IEEE 802.3af Class 1
Terminal block 12-48VDC
52 x 95 x 27 mm
-25 to 75C (special components required)
DIN-rail mounting

146.06 €
Item numberSERIA-DEVIC-SERVE-RS-16
On the way in
HART to RS-232/422/485 Gateway, Modbus RTU/ASCII, 1 Port

1 x HART port, 2 or 4-wired devices
RS-232 (3-wire) / RS-422 / RS-485
Modbus RTU / Modbus ASCII protocol
Point to Point or Multi-Drop topology
Max. 15 HART devices, Burst Mode support
Loop power output +30V
Loop resistor 250 Ohm (1W) via DIP-switch
Isolation per UL1577 spec
Reverse polarity and brown-out protection
10-30VDC, 3.5W max
25 x 116 x 120 mm, DIN-Rail
-25 to +75C (special components required)

471.68 €
Item numberHART-RS-232-422
On the way in
Serial Device Server RS-485/422 to Ethernet with PoE, 2x RJ45

32-bit ARM CPU
2 x 10/100 Base-TX RJ45, PoE 802.3af
1 x RS-485/422, isolated
Baud rate up to 115200 bps
Bias resistor 1 K Ohm
Parity: None, Odd, Even, Mark, Space
Data bit 5-8, stop bit 1-2
Max. 254 node addresses
DIN-rail mounting, plastic casing
12-48VDC or PoE 802.3af Class 1
97 x 33 x 126 mm
-25 to +75C (special components required)

191.62 €
Item numberSERIA-DEVIC-SERVE-RS-13
On the way in
Serial Device Server, 2-Port RS-232 to Ethernet with PoE

2 x RS-232, 1000VDC isolation
1 x 10/100 Base-TX RJ45 PoE
IEEE 802.3af Class 1 PoE
Auto-negotiating, Auto-MDI/MDIX
Baud rate up to 115200 bps
Data bit 5/6/7/8, Stop bit 1/2
Parity None/Odd/Even/Mark/Space
DIN-Rail mounting, plastic casing
12-48VDC or PoE powered
52 x 95 x 27 mm
25 to 75C (special components required)

150.08 €
Item numberSERIA-DEVIC-SERVE-PORT-2
On the way in
Programmable Modbus Gateway RS-232/RS-485 to Ethernet DIN-Rail

CPU 80188, 40MHz compatible
1 x RS-232, 1 x RS-485 port
1 x RJ-45 10Base-T Ethernet
Baud rate up to 115200bps
Real Time Clock built-in
Watchdog Timer
Flash 512KB, SRAM 512KB
DIN-Rail mounting
OS: MiniOS7
-25-75C (special components required)
10-30VDC power input
72 x 123 x 33 mm

330.98 €
Item numberPROGR-MODBU-GATEW-RS
On the way in
HART to RS-232/422/485 Gateway, Modbus RTU/ASCII, 1-Port

1-port HART gateway
RS-232 (3-wire) / RS-422 / RS-485
Modbus RTU / Modbus ASCII protocol
Supports 2-wire or 4-wire HART devices
Point to point or multi-drop topology
Up to 15 HART devices
Burst mode supported
Baud rate up to 115200 bps
10-30VDC power input
72 x 35 x 121 mm (W x L x H)
-40 to +75C operating temp
DIN-rail or wall mounting

463.64 €
Item numberHART-RS-232-422-3
On the way in
HART to Fiber Gateway, RS-232 Single Mode 100Base-FX SC

HART Gateway with fiber conversion
1 x HART port, 2-pin terminal block
RS-232 configuration port (1200,O,8,1)
SC Duplex, Single mode, 100Base-FX
Wavelength 1310 nm
TX Output 15 dBm min, -8 dBm max
RX Sensitivity 34 dBm max
Selectable 250 Ohm loop resistor
Isolation per UL1577
Reverse polarity and brown-out protection
10-90% RH non-condensing
10-30VDC, 33.0 x 126 x 101 mm

513.22 €
Item numberHART-FIBER-GATEW-RS
On the way in
Programmable Modbus Gateway, RS-232/RS-485 to Ethernet DIN-Rail

RS-232/RS-485 to Ethernet Gateway
80188 CPU, 40 MHz
1 x RJ-45 10Base-T Ethernet
1 x RS-232, 1 x RS-485
Baud rate up to 115200 bps
2KB EEPROM, 512KB Flash, 384KB SRAM
Watchdog Timer
DIN-Rail mounting
-25~75°C (special components required)
10-30VDC, 2.0W
72 x 112 x 33 mm

218.42 €
Item numberPROGR-MODBU-GATEW-RS-3
On the way in
Programmable Modbus Gateway with RS-232/RS-485, RJ-45 10Base-T, DIN-Rail

CPU 80188, 40 MHz
512KB Flash, 384KB SRAM, 2KB EEPROM
Watchdog Timer
5-digit 7-segment LED display
1 x RJ-45 10Base-T Ethernet port
1 x RS-232, 1 x RS-485 port
Baud rate up to 115200 bps
DIN-Rail mounting
5-90% humidity, non-condensing
-25~+75°C (special components required)
10-30VDC, 3.0W
72 x 112 x 33 mm

246.56 €
Item numberPROGR-MODBU-GATEW-RS-5
On the way in
CANopen to PROFIBUS DP-V0 Gateway, DIN-Rail, -25 to +75°C

CANopen DS-301 to PROFIBUS DP-V0
NXP SJA1000T CAN controller, 16MHz
Profichip VPC3+C PROFIBUS controller
CAN baud rate up to 1Mbps
PROFIBUS baud rate up to 12Mbps
Isolated: CAN 1000VDC, PROFIBUS 3000VDC
RS-232 port for firmware update
Built-in watchdog timer
PWR, RUN, ERR status LEDs
DIN-rail mount, 2.5W consumption
72 x 33 x 119 mm
-25 to +75C operating temperature

479.72 €
Item numberCANOP-PROFI-DP-V0
On the way in
Programmable Modbus Gateway with RS-232/485, RJ-45 Ethernet, DIN-Rail

CPU 80188, 40MHz compatible
Watchdog Timer
5-Digit 7-Segment LED Display
1 x RJ-45 10Base-T Ethernet
1 x RS-232, 1 x RS-485
Baud Rate up to 115200bps
DIN-Rail Mounting
Operating Temp -25 to +75C
10-30VDC, 3.0W
72 x 112 x 33 mm

246.56 €
Item numberPROGR-MODBU-GATEW-RS-4
On the way in
HART to Modbus Gateway, RS-232/422/485, 1-Port HART Interface

1 x HART port, 2/4-wire devices
Modbus RTU / Modbus ASCII
RS-232(3-wire) / RS-422 / RS-485
Point to Point or Multi-Drop
Max. 15 HART devices
Burst mode supported
Baud rate up to 115200
Loop resistor 250 Ohm via jumper
Isolation per UL1577
10-30VDC, 1W consumption
72 x 35 x 121 mm
-25 to 75C (special components required)

443.54 €
Item numberHART-MODBU-GATEW-RS
On the way in
3G/4G Gateway with GPS, RS-232/485, CAN Bus and Ethernet

ARM CPU with Watchdog Timer
3G/4G: LTE, DC-HSPA+, TD-SCDMA, CDMA2000
LTE up to 100 Mbps Downlink
GPS/GNSS NMEA 0183, 32 Channels
1 x RJ-45 10/100Base-T(X)
1 x RS-232 Console/Debug, 1 x RS-232
1 x RS-485 3000VDC Isolated
CAN Bus (CAN_H, CAN_L)
SD Card slot, Max. 32GB SDHC
Metal casing, DIN-Rail/Screw mount
4.8W (200mA @ 24VDC)
-25 to 75C (special components required)

1,031.80 €
Item number3G-4G-GATEW-GPS
On the way in
HART Gateway with RS-232, 1-Port, Ethernet 10/100Base-TX

1x RS-232 HART port (3-wire)
10/100Base-TX Ethernet, Auto-MDIX
Supports 2-wire or 4-wire HART devices
Point-to-Point or Multi-Drop topology
Up to 15 HART devices
Short and Long Frame support
Burst mode supported
250 Ohm loop resistor via jumper
Isolation per UL1577
DIN-Rail or wall mounting
10-30VDC input, 1W consumption
72 x 35 x 121 mm

564.14 €
Item numberHART-GATEW-RS-232
On the way in
3G/4G Gateway with GPS, RS-232/485, CAN Bus and Ethernet

ARM CPU processor
LTE FDD B1/B3/B5/B7/B8/B20
DC-HSPA+ up to 42 Mbps downlink
GPS/GNSS NMEA 0183, 32 channels
1 x RJ-45 10/100Base-T(X)
2 x RS-232, 1 x RS-485 isolated
CAN Bus interface
SD card slot, max 32GB SDHC
Watchdog timer
Metal casing, DIN-rail mount
-25 to +75C (special components required)
24VDC, 4.8W consumption

979.54 €
Item number3G-4G-GATEW-GPS-3
On the way in
Showing 21-40 of 54 item(s)