Item number CANOP-EMBED-CONTR-2X

CANopen Embedded I/O Controller, 2x AI, 2x AO, 4x DI, 4x DO, -25 to 75°C

CANopen protocol (CiA 301, CiA 401)
2x Isolated Analog Input, 16-bit
2x Analog Output, 12-bit
4x Digital Input, Wet Contact
4x Digital Output, Open Collector
Baud Rate 10kbps - 1Mbps
Built-in 120 Ohm Terminal Resistor
Node ID 1-99, 10 RxPDO/TxPDO
Hardware Watchdog, 3 Status LEDs
DIN-Rail Mounting
-25 to +75C Operating Temperature
33 x 99 x 78 mm

379.22 €
Excl. VAT
Quantity
On the way in
file_download DOWNLOADS

Specifications

Installation DIN-Rail
Isolation 3000 VDC for DC-to-DC, 2500 Vrms for photo-couple
Type +0V ~ +5V, +/-5V, +0 V ~ +10V,+/-10VIsolated Open Collector (Sink)Wet contact (Sink)
Operating Temperature -25 ~ +75 °C
Resolution 16-bit12-bit
Terminal Resistor Built-in 120Ω
Watchdog Timer Hardware watchdog
Status 3 LEDs to PWR, RUN and ERR
Consumption 1.8 W
Dimensions (mm) 33 x 99 x 78 ( W x L x H )
Storage Temperature -30 ~ +80 °C
Humidity 10 ~ 90% RH, Non-condensing
Overload Protection Yes
Short-circuit Protection Yes
Channels 242 (Differential)
Accuracy +/- 0.1% of FSR+/-0.1% of FSR
Sampling Rate 60 Samples/Sec. (Total)
Input Impedance 10 KΩ, 0.66W
Overvoltage Protection 60 VDC70 VDC
Zero Drift +/- 10 μV/ °C
Span Drift +/-25 ppm/ °C
Voltage Output Capability 10 V @ 20 mA
Current Load Resistance 500 Ω
Power-on Value Yes
Safe Value Yes, ProgrammableYes
ON Voltage Level +3.5 ~ +30 VDC
OFF Voltage Level +1 VDC Max.
Load Voltage +3.5 ~ +50 VDC
Load Current 700 mA/channel Max.
Power on Value Yes, Programmable
Baud Rate 10 k ~ 1 M
Sensor Type ±10V, ±5V, ±2.5V, ±1.25V, ±1V, ±500mV, ±250mV
Common Mode Rejection 86 dB Min.
Normal Mode Rejection 100 dB
Individual Channel Configuration Yes
Protocol CiA 301 v4.02, CiA 401 v2.1
Node ID 1 ~ 99
No. of PDOs 10 RxPDO , 10 TxPDO
Error Control Node Guarding protocol / Heartbeat Producer
NMT Slave
EMCY Message Yes
PDO Mode Event-triggered, remotely-requested, Cyclic and acyclic SYNC

CANopen I/O Controller

This CANopen I/O controller is a DIN-rail mounted embedded module for integrating analog and digital signals into a CAN bus network. It combines isolated analog and digital inputs and outputs with a fully compliant CANopen slave interface, making it suitable for automation and process control applications.


2x Isolated Analog Input (16-bit) · 2x Analog Output (12-bit) · 4x Digital Input / 4x Digital Output · CiA 301 / CiA 401 CANopen Protocol


Key Features

  • Isolated Analog I/O - protects sensitive signals from noise and ground loops
  • CANopen Slave Interface - full compliance with CiA 301 and CiA 401 profiles
  • Hardware Watchdog - ensures reliable operation in unattended installations
  • Programmable Power-on and Safe Values - defines safe outputs at startup or communication loss
  • Wide Operating Temperature - reliable performance from -25 to +75 degrees C


Typical Applications

The controller is designed for industrial environments where analog and digital signals need to be transmitted reliably over a CAN network.

  • Factory automation and process monitoring
  • Remote sensor and actuator interfacing
  • Machine condition monitoring
  • Distributed I/O in industrial networks


A robust, DIN-rail mountable CANopen I/O solution for demanding industrial environments.