EtherCAT Masters

EtherCAT Masters

EtherCAT master controllers manage a network of EtherCAT I/O modules, motor drives and sensors in real time. They typically sit as the central unit in a machine or production line, reading digital and analog signals and sending commands to actuators and motors with cycle times down to less than a millisecond. The controller mounts on a DIN rail and usually runs on 24VDC.

Choose based on how many axes and I/O points the application requires, and whether stepper motor control is needed or simply digital and analog signal reading. Look at channel count, resolution on analog inputs, cycle time and which serial ports such as RS-232, RS-422 or RS-485 are needed to connect other equipment. The operating temperature range matters if the controller will sit in a hot or cold machine room.

EtherCAT Masters
There are 55 products.
Compact EtherCAT Master PAC with 32-Channel Digital Input

32 x Digital Input, Wet/Dry
EtherCAT, 2 x RJ45 Ports
Node ID up to 256
Cycle Time 100 us
Distributed Clocks Support
Isolation 3750 VDC
Metal Casing, IP40
DIN-Rail or Wall Mounting
-25 to 75C (special components required)
24VDC, 3W Consumption
83 x 122 x 65 mm

272.02 €
Item numberCOMPA-ETHER-MASTE-PAC-14
On the way in
Compact EtherCAT Master PAC with RS-422/485, PoE, DIN-Rail

EtherCAT Master, Web Config Interface
1 x EtherCAT RJ-45, Cat 5e min.
1 x RS-422/485, Modbus RTU Slave
Modbus TCP/UDP, OPC UA, HTTP(S)
IPv4, IPv6, SNTP support
Cycle Time 0.125 - 32ms
Distributed Clocks Supported
PoE IEEE 802.3af, Class 2
12-48VDC Terminal Block Power
119 x 31 x 157 mm (W x L x H)
-25 to +75C (special components required)
DIN-Rail Mount, Plastic Casing

1,051.90 €
Item numberCOMPA-ETHER-MASTE-PAC-15
On the way in
Compact EtherCAT Master PAC, 1-Axis Stepper Motor Control, 0.5ms Cycle

EtherCAT Master PAC, 1-axis control
Stepper motor control, 2 phase
Peak current 1.5A/phase output
Microstepping up to 256
Cycle time 0.5ms, distributed clock
2 x RJ45 EtherCAT ports
2 x limit position inputs
1 x open collector output
Metal casing, DIN-rail/wall mount
20-30VDC power input
33 x 120 x 116 mm (DIN-rail)

353.76 €
Item numberCOMPA-ETHER-MASTE-PAC
On the way in
EtherCAT Master PAC 16-CH Thermocouple Input Module, 16-bit

16-channel thermocouple input
Types J K T E R S B N C L M
16-bit resolution
Accuracy +/-0.1% of FSR at 25C
Sampling rate 100Hz per channel
Open wire detection
EtherCAT, 2 x RJ45, up to 256 nodes
Distributed clocks, cycle time 100us
Metal casing IP40
DIN-rail or wall mounting
24VDC input, 1.60W consumption
83 x 122 x 65 mm

948.72 €
Item numberETHER-MASTE-PAC-16-4
On the way in
Compact EtherCAT Master PAC, 2 x RJ45, DIN-Rail, 24VDC

EtherCAT Master PAC
2 x RJ45 EtherCAT ports (OUT)
Max. 100m between stations
CAT5 shielded Ethernet cable
EFT: 1KV Class B (IEC 61000-4-4)
ESD: +/-8KV Air (IEC 61000-4-2)
Plastic casing
DIN-Rail or wall mounting
24VDC, 1.5W max consumption
31 x 108 x 74 mm (W x L x D)
-25 to +70C operating temp
10-90% RH non-condensing

123.28 €
Item numberCOMPA-ETHER-MASTE-PAC-16
On the way in
Compact EtherCAT Master PAC with RS-232/422/485, Modbus RTU, DIN-Rail

EtherCAT Master PAC, compact design
1 x RS-232/422/485 port
Modbus RTU slave protocol
2 x RJ-45 Ethernet/EtherCAT
Max. 100m between stations
Cycle time 10 ms
Reverse polarity protection
DIN-Rail mounting, plastic casing
12-48VDC, 0.1A @ 24VDC
-25 to +75C (special components required)
33 x 127 x 99 mm
10-90% RH, non-condensing

384.58 €
Item numberCOMPA-ETHER-MASTE-PAC-19
On the way in
8-Channel Analog EtherCAT I/O Module, 12-bit, DIN-Rail

8-channel analog I/O module
EtherCAT interface, 2 x RJ-45
Ranges: +/-5V, +/-10V, 0-20mA
12-bit resolution
Accuracy +/-0.1% FSR
Cycle time 1 ms
Distributed clocks support
DIN-rail mounting
4W max consumption
10-30VDC power input
-25/75°C (special components required)
33 x 127 x 108 mm

333.66 €
Item numberCHANN-ANALO-ETHER-MODUL
On the way in
16-Channel EtherCAT I/O Module, Open Collector, DIN-Rail, -25 to 75°C

16 x Digital Output Channels
Open Collector Sink/Source NPN/PNP
2 x RJ-45 EtherCAT Ports
200 us Cycle Time
Distributed Clocks Support
Isolation 3750 Vrms
DIN-Rail Mounting
Load Voltage 3.5-30VDC, 100mA/CH
Power Input: 10-30VDC, 4W Max
Dimensions: 33 x 127 x 108 mm
Operating Temp: -25 to 75C
Humidity 10-90% RH

172.86 €
Item number16-CHANN-ETHER-MODUL-3
On the way in
EtherCAT Analog Input Module, 8/16-CH, Voltage/Current, 12-bit

8 differential / 16 single-ended CH
Voltage and current input types
12-bit resolution, 0.2% accuracy
Sampling rate 1kHz per channel
EtherCAT, 2 x RJ-45 ports
Cycle time 1 ms
Overvoltage protection +/-35VDC
EFT/ESD/Surge protected
DIN-Rail mount, plastic casing
Power input 10-30VDC, 4W max
Dimensions 33 x 127 x 108 mm
-25 to +75C operating temp

436.84 €
Item numberETHER-ANALO-INPUT-MODUL-2
On the way in
EtherCAT Master PAC, 32-Channel Open Collector Sink Output, 24VDC

32 x Open Collector Sink Output
Internal flywheel diode
Load: 40VDC / 150mA per channel
Isolation: 3000VDC
2 x RJ45 EtherCAT ports
Node ID up to 256
Cycle time: 100us
Distributed Clocks support
Metal casing, IP40
-25 to +75C (special components required)
24VDC, 3W consumption
83 x 122 x 65 mm

290.78 €
Item numberETHER-MASTE-PAC-32
On the way in
EtherCAT Analog Input Module, 8 Differential/16 SE Channels, 16-bit

8 Differential or 16 Single-ended Ch
Voltage/Current Input, Software Sel.
16-bit Resolution, 0.05% Accuracy
1kHz Sampling Rate per Channel
2 x RJ-45, EtherCAT (CAT5 min)
1 ms Cycle Time
Overvoltage Protection ±35VDC
DIN-Rail Mounting, Plastic Casing
+10 to +30VDC Input, 4W Max
33 x 127 x 108 mm (W x L x H)
-25 to +75C Operating Temp

700.82 €
Item numberETHER-ANALO-INPUT-MODUL-3
On the way in
Compact EtherCAT Master PAC, 8DI/8DO, DIN-Rail, -25~75C

8 x Digital Input Dry+Wet Contact
8 x Digital Output Open Collector
Isolation 3750 VDC/Vrms
2 x RJ-45 EtherCAT Ports
Cycle Time 200 us
Distributed Clocks Support
Load Current 700 mA/Channel
DIN-Rail Plastic Casing
10-30VDC, 4W Max.
33 x 127 x 108 mm
-25 to 75C (special components required)
10-90% RH Non-condensing

188.94 €
Item numberCOMPA-ETHER-MASTE-PAC-9
On the way in
Compact EtherCAT Master PAC, 2x RJ-45, RS-232/422/485, Modbus RTU

EtherCAT Master PAC, DIN-Rail
2 x RJ-45 Ethernet/EtherCAT
1 x RS-232/422/485
Modbus RTU protocol
Cycle time 10 ms
Max 100m between stations (100BASE-TX)
Min. CAT 5e cable required
Reverse polarity protection
Plastic casing
12-48VDC, 0.1A @ 24VDC
33 x 127 x 99 mm (WxLxH)
-25 to 75C (special components required)

402.00 €
Item numberCOMPA-ETHER-MASTE-PAC-18
On the way in
Compact EtherCAT Master PAC with Modbus RTU, 2x RJ-45, RS-232/422/485

EtherCAT Master PAC, compact design
Modbus RTU Master protocol
1 x RS-232/422/485 port
2 x RJ-45 Ethernet/EtherCAT
Max. 100m station distance
Cycle time 10 ms
Reverse polarity protection
Plastic casing, DIN-Rail mount
12-48VDC, 0.1A @ 24VDC
-25 to 75C (special components required)
33 x 127 x 99 mm
10-90% RH non-condensing

384.58 €
Item numberCOMPA-ETHER-MASTE-PAC-17
On the way in
Compact EtherCAT Master PAC, 2-Axis Encoder Counter, DIN-Rail

EtherCAT Master PAC, 2 x RJ-45 ports
2 x Encoder Counter Axes, 32-bit
Modes: A/B Phase, CW/CCW, Pulse/Dir
8 x Digital Input status
Photo-isolation 2500VDC
Cycle Time 0.5ms, Distributed Clock
ESD 4KV, EFT/Surge 1KV protection
DIN-Rail, UL94V-0 housing
+20-30VDC power input
110 x 90 x 33 mm (LxWxH)
-25~+75C (special components required)
Humidity 10-90% RH non-condensing

344.38 €
Item numberCOMPA-ETHER-MASTE-PAC-5
On the way in
Compact EtherCAT Master PAC, 16-Channel Relay Output Module

16 x Form A (SPST-NO) relay output
3A @ 30VDC / 3A @ 250VAC contact
2 x RJ-45 EtherCAT ports
100m max distance (100Base-TX)
Cycle time 200 us
Distributed clocks support
Isolation 3000VDC
DIN-Rail plastic casing
10-30VDC input, 4W max
31 x 157 x 126 mm (WxLxH)
-25 to 75C (special components required)
10-90% RH non-condensing

234.50 €
Item numberCOMPA-ETHER-MASTE-PAC-22
On the way in
EtherCAT Master PAC with 16 DI, 16 DO, 2x RJ-45, -25~75C

16 x Digital Input, Dry+Wet Contact
16 x Digital Output, Open Collector NPN
2 x RJ-45 EtherCAT, 100m Max
Cycle Time 1 ms
Distributed Clocks Support
Isolation 3750 VDC/Vrms
Load Current 700 mA/Channel
DIN-Rail Mounting, Plastic Casing
10-90% RH Non-condensing
10-30VDC Input, 4W Max
-25 to 75C (special components required)
31 x 157 x 126 mm (W x L x H)

253.26 €
Item numberETHER-MASTE-PAC-16-2
On the way in
EtherCAT Master PAC with 16 Dry/Wet Digital Inputs, DIN-Rail

EtherCAT Master PAC, 16 channels
Dry and Wet contact input type
Sink/Source (NPN/PNP) support
2 x RJ-45 EtherCAT ports
Cycle time 200 us
Distributed Clocks support
Isolation 3750 VDC
ESD +/-4kV, EFT +/-1kV, Surge +/-1kV
+10 to +30VDC input
33 x 127 x 108 mm
-25 to +75C (special components required)
DIN-Rail plastic casing

180.90 €
Item numberETHER-MASTE-PAC-16
On the way in
Compact EtherCAT Master PAC, 8 DI / 8 DO, DIN-Rail

EtherCAT Master PAC, DIN-Rail
8 x Digital Input, Wet Contact
8 x Digital Output, Open Collector
PNP Source, 100 mA/Channel
2 x RJ-45, 100Base-TX
Cycle Time: 200 us
Distributed Clocks Support
Isolation 3750 VDC/Vrms
10-30VDC, 4W Max.
33 x 127 x 108 mm
-25 to 75C (special components required)

160.80 €
Item numberCOMPA-ETHER-MASTE-PAC-11
On the way in
Compact EtherCAT Master PAC 8DI/8DO NPN, DIN-Rail, -25~75C

EtherCAT Master PAC, DIN-Rail
8 x Digital Input, Wet Contact
8 x Digital Output, Open Collector NPN
2 x RJ-45, Cat5 shielded
Cycle Time 200 us
Distributed Clocks support
Isolation 3750 VDC/Vrms
EFT, ESD, Surge protection
10-30VDC, 4W Max.
33 x 127 x 108 mm (W x L x H)
-25 to 75C (special components required)
Humidity 10-90% RH, non-condensing

160.80 €
Item numberCOMPA-ETHER-MASTE-PAC-12
On the way in
Showing 1-20 of 55 item(s)