Item number SGA/GT-A
Load Cell amplifier, Strain Gauge Signal conditioner, 2mV/V, 4-20mA 0-5V, 0-10V, 5-12VDC
Load cell amplifier with 4-20mA, 0-5V, 0-10V
2.0 mV/V ± 10% sensitivity, better than 0.1% FS accuracy.
Internal precision amplifier and conversion circuits.
DIN rail mounted
Terminal blocks.
4-20 mA current and 0-5 V, 0-10 V voltage output in one amplifier
The output signal can be selected via a push button
Can be used with all kinds of strain gauge bridge load cells such as weighing, tension, compression, torque, etc.
Dimensions: 115 x 58 x 37
Temperature: -10 - +50°C
81.07 €
Excl. VAT
Quantity
On the way in
The SGA/GT-A is a DIN rail mounted load cell amplifier that accepts mV load cell signal input and converts it to 4-20mA and 0-5V/0-10V output.
It can be used with various types of Strain Gauge load cells to measure and monitor weight, force, tension, etc. signals.
This load cell amplifier can filter and amplify a small mV electrical signal and convert it to standard DC current 4-20mA, voltage 0-5V, 0-10V signal.
Suitable for PLC or other control system data acquisition. The internal embedded active low-pass filter can effectively filter electromagnetic interference in industrial sites.
Other products in the same category:
Strain Gauge Amplifier Signal Conditioner - Digital Version, 4x 350 Ohm Bridge Excitation, Selectable Analogue Output, IP65
Strain gauge signal conditioner
DC powered version (SGA/D)
18 to 24 V DC input
Isolated PSU option: 9 to 36 V DC
90 mA typical current draw
Bridge excitation: 5 V and 10 V
Bridge sensitivity: 0.06 to 30 mV/V
Bandwidth DC to 6000 Hz
Filter cut-off: 1 to 5000 Hz
Outputs: +-10V, +-5V, 0-10V, 0-5V
Outputs: 0-20 mA, 4-20 mA
IP67 ABS case, 3 x M16 glands
-10 to 50 degrees C operating
164 x 84 x 57 mm
487.76 €
Item number:SGA/D
Programmable Load Cell Instrument and controller, LCD Display, Connection up to 16 Load Cell, IP66 NMEA 4X
Top-class weighing instrument from Interface
LCD screen, W x H - 117 x 86 mm
Display up to four channel channels per screenshot
With required Legal for Trade information
32 scale accumulations
Millivolt calibration, 5-point linearization and geographic calibration
NEMA Type 4X / IP66 stainless steel enclosure
Selectable A/D with measurement speed up to 960/second
100 set points, 30 configurable
64K uses built-in Non-V RAM
Power for 16, 350 ohm load cells per A / D card
Peak team
Call +45 56 66 20 20 for price
Item number:LC-920I-UNI
Portable load cell instrument. 4 Wire Strain Gauge input. Single pass calibration, direct, mV/V with TEDs
Handheld 7-digit LCD screen
4 Wire Full Bridge input
with Peak, Trough, Net, Overload and Shunt Cal Indication
Battery operation of 450 hours in power saving mode
Keys for ON / OFF , Interval Selection, Peak / Valley Hold and Gross / Net
Single Calibration (Direct mV/V) with double range for values such as kg and lb
Weighing only 250 grams
IP65 / NEMA4
TEDs Enabled to automatic Sensor calibration (IEEE1451 - Template 33)
Buy Leather case
Battery: 2 x AA
1,146.24 €
Item number:INST-LOADCELL-HH
Portable load cell instrument for strain gauge input. Multi-point calibration, direct, mV/V. Logging and graphing. With TEDs
Sovereign Linearity Specifications
Excitation Voltage: 3.3Volt
Resolution: 24bit
% FS: 0.0002
Measurement speed up to 2400 samples per. Second
High internal resolution (up to 500,000 Counts)
IP67 Searched cabinet
Battery powered (long battery life)
128 x 64 Graphic screen with backlight
More display modes (Peak / bottom, Delta, Live , gross and net)
logging and graphing for PC (software is included)
support Ted's template 33, 40 and 41
Live calibration and multi-point calibration
Dim: 170 x 94 x 42 mm
Weight: 330 grams
1,880.96 €
Item number:INST-LOADCELL-PSD








