Item number X-410-I
Web Enabled Programmable Controller with Log, 4 x Digital in, 4 x Relay Out COM NO Common Com, 1-Wire Bus, P2P, 9 - 28VDC
Web based controller with I/O, 1-wire bus
4 x digital inputs (Common GND)
1-wire bus, max. 16 sensors (temp / moisture etc.)
Permissions: Administrator, Manager, User
Tasks
50 Scheduled
50 Conditional
16 Automatic Restart
20 Over Rule Terms
E-mail Alarms by defined conditions
Supports encrypted e- Mail servers such as Gmail
RTC with NTP server synchronization
No software Required
Basic Script Support for Advanced Flexibility
Configurable Logging
Graph (Logged Data)
HTTPS / TLS encrypted
Static or DHCP IP Address Configuration
Modbus, SNMP, Remote Service, IP Filtering
On-site update
Supply voltage: 9 - 28VDC
616.53 €
Excl. VAT
Quantity
On the way in
Web-enabled programmable controller.
X-410-I have 4 digital inputs, 4 relays, 1-wire bus for a maximum of 16 1-wire sensors and a built-in web server that enables remote access from many devices along with Infinite governance and monitoring options. Has built-in 4 relays (1A at 28VAC, 24VDC) with common com to e.g. Low voltage, engines, locks, solid state relays (associated with larger loads). 4 digital inputs (optoized 4-26VDC). Monitor to / from mode or configure as digital counters or frequency measurement. It can be used to monitor switches, alarm sensors, level sensors, flow sensors and more. Up to 16 temperature / humidity sensors on the same 1-wire bus.
Monitor up to 16, 1-wire sensors such as: Temperature and moisture sensors (not supplied). X-410 - I support peer-to-peer communication between ControlByWeb modules. It supports communication with up to 32 modules and allows you to check and monitor up to 100 I / O channels. The X-410 - I can communicate with all ControlByWeb devices, but offers immediate message between products in the X-400 series, which means that X-410 can control and monitor I / O on other products in the X-400 series, which whether it was directly connected to the module. The X-410-I's built-in interface allows you to create custom "tasks" for simple and advanced control logic. Easily create tasks based on time, input or output status or device response. Create up to three actions for each task so you get the ultimate control and monitoring solution for your application. Create up to 50 planned, 50 conditional, 16 automatic restart tasks and 20 overlay plans.
I / O Task Builder is conditional tasks triggered depending on I / O status. Conditional tasks are often used to send alarms at high / low temperature, control alarms, etc.
Scheduled tasks perform actions on preset times at specific days. You can also choose to override these scheduled tasks at specific days (ie holidays). Scheduled tasks are often used for controlling light columns for parking space, stadium light, magnetic locks, generators, etc.
Advanced logic from restarting devices automatically (cameras, routers, servers, etc.) when they do not respond. Also write Basic script for more advanced logic.
X-410-I allows you to log a number of data points as local and external I / O, registers, tasks and excitement. Log inputs can be made with preset intervals, scheduled times, triggered by I / O changes or logical events. Plan a daily log file to be sent by e-mail or uploaded via FTP server. Graphing of the current log file and see I / O status over time.
24VDC 1.7A (40Watt) power supply from 100-240VAC, DIN rail
AC / DC power supply for DIN rail mounting
100-240V AC, 50 / 60Hz, 1.1A
Output, 24V, 1.7A (40 Watt)
Screw terminal
Adjustable output voltage
Short-circuit, overload and surge protection
Compact dimensions: 40 x 100 x 90 mm
Working temperature: -20-70 ° C
44.89 €
Item number:DC24V1.7A-D
24VDC 60W Power supply from 85VAC-264VAC. 24V / 2.5A, adjustment 21.6-29V, DIN mounting
AC / DC power supply for your rail mounting
AC Input: 85 - 264Vac
Effect: 60W
Output voltage: 24V / 2.5A
Screw terminal
Adjustable output voltage for 24 to 29V
Working temperature: -30 - + 70 ° C
Dimensions: 90 x 54.5 x 62.5 mm (H, D, B)
48.91 €
Item number:DC24V2.5A-D
24VDC 60W power supply. Ultra wide AC input from 180VAC-550VAC. 24V/2.5A, Fine adjustment from 24-29V, DIN mounting
AC/DC power supply for DIN rail mounting
AC input: 180 - 550VAC
Power: 60W
Output voltage: 24V / 2.5A
Screw terminal
Adjustable output voltage to 24 to 29V
Working temperature: -30 - +85°C
Dimensions: 125 x 102 x 32 mm (H, D, W)
95.94 €
Item number:DC24V2.5A-D+
Other products in the same category:
3 x temperature measurement with PT100, PT1000 sensor and nine RTD elements, 16bit resolution, RS485 bus. 10 - 30vdc.
Module for PT100 or PT1000 sensor with 4-, 3- or 2-wire
for nickel temperature sensor (Ni RTD)
16 bit resolution
15 Measurements per second (Total)
Supply voltage: 10 - 30vdc / 1 Watt
Master RS485 must establish bias voltage
Dim: 123 x 72 x 35 mm
378.95 €
Item number:M485-ADRTD3-I
Logic Controller with Data Logger. 1 x RJ45 Ethernet, 1 x RS232, 1 x RS485. Supports XV plug-in I/O board, 12 - 48VDC
The logger / controller with socket for internal I / O expansion bus (eg. Relay module)
is programmed with simple logic functions
IF-THEN-ELSE, AND and OR simplifies the setup
supports SNMP, SMTP , FTP, Modbus RTU and DCON
Ethernet 10/100 / 1000Mbit
setup via the integrated Web server
1 x RS232 ports
1 x RS485 ports
Supply voltage: 12 - 48VDC
712.21 €
Item number:L-CON-LOG
CAN bus repeater. Amplifier and restores correct pulse shape. Up to 800kbps. Opto-isolated. DIN bracket.
CAN Bus Booster
CAN specification 2.0A and 2.0B
ISO 11898-2 standard
Max. Baudrate: 800 Kbps
Jumper for 120Ω Terminal resistance on the CAN bus
2 CAN channels
Automatic Baud Rate
Up to 100 nodes on each CAN port
Removable terminal block
DIN bracket
Supply: 10 - 30vdc
Call +45 56 66 20 20 for price
Item number:M485-CAN-I+
Network Module with Digital I / O Korenix Jeti / O 6550
Network module with digital I / O Korenix JETI / O 6550
Channels: 14/8
Digital inputs: 14 pcs., Logic 0: 0 - 4 V, Logic 1: 5 - 30V
Digital outputs: & nbsp; 8 pcs. Open collector, 5 - 40 V 250mA
Isolation: Optical 2500 VRMS for analog and digital inputs and outputs for the power supply
Magnetic 1500 V from the network interface for the power supply
10/100 Mbit m / RJ45 their connector
Operating temperature: - 25 ° C - 70 ° C
Supports Modbus / TCP, OPC server, SNMP. Software included for configuration
For DIN rail mounting
Supply: 10 - 30 VDC via terminal block, Max 1.92 W
186.80 €
Item number:ETHIO14D8D-K
Programmable Industrial Controller with 8 Digital inputs and 4 Relay outputs
ARM Cortex - A53 CPU , 1.2 GHz
RAM 1Gb SDRAM
16GB of memory
2 x RS232/422/485
8 x DI and 4 x relay outputs
DC input 9-32V
4G module
OS : Linux Raspbian
User need knowledge of linux and programing
Documentation for DI/O and 4G module
766.88 €
Item number:RPI-4G-8I4O
HMI 4.3" Controller Panel with touch, RS485 bus, MODBUS RTU, GUI design, C and Ladder. RTC. 12 - 48VDC
4.3" HMI Control panel for I/O modules
LCD color display with touch
Free HMIWorks development tool
Library for useful applications
MODBUS
RS485 serial port
Supply voltage: 12 - 48VDC, 2.5W
Dimensions: 126 x 92 x 29 mm
Wall mounted in wall back piece 86 x 86 mm
Operating temperature: -20 - +50°C
299.89 €
Item number:HMI4.3"SER-I
Industrial controller for measuring and controlling the processes. With ethernet and 4G, with data logging, MQTT, IoT
Advanced Controller with logging
With slot for internal I/O expansion module, A/D, D/A, D/I, D/O, relay
Program with simple logic functions - WISE (Web Inside Smart Engine)
Logic functions with IF-THEN-ELSE logic
Supports SNMP, SMTP, FTP, MQTT, Modbus / TCP / RTU and DCON
Ethernet 10/100 / 1000Mbit
Setup via the built-in Web server
1 x RS232 port
2 x RS485 port
Supply voltage: 12 - 48VDC
1,188.98 €
Item number:L-CON-LOG+4G













